1. Scope

p>1.1 This specification covers the chemical, mechanical, and dimensional requirements for metric hardened steel washers for use with fasteners having nominal thread diameters M12 through M100. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners. These washers are suitable for use with fasteners covered in Specifications A 325M, A 490M, A 563M and with fasteners of Specification F 568 property classes 8.8 and higher.

1.2 The types of washers covered in this specification are:

1.2.1 Type 1Washers made of carbon steel.

1.2.2 Type 3Washers made of steel having atmospheric corrosion resistance and weathering characteristics comparable to that of steels covered in Specifications A 242/A 242M, A 588/A 588M, and A 709. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition. See 5.1. When properly exposed to the atmosphere, these steels can be used bare (uncoated) for many applications.

1.3 The styles of washers covered in this specification are:

1.3.1 Circular WashersCircular washers in nominal sizes 12 mm through 100 mm, are suitable for applications where sufficient space exists and angularity permits.

1.3.2 Beveled WashersBeveled washers are square and rectangular, in nominal sizes 12 mm through 36 mm, with a beveled 1:6 surface for use with American Standard beams and channels.

1.3.3 Clipped WashersClipped washers are circular or beveled for use where space limitations necessitate that one side be clipped.

Note 1This specification is the metric counterpart of Specification F 436.

1.4 Terms used in this specification are defined in Terminology F 1789 unless otherwise defined herein.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

A242/A242M Specification for High-Strength Low-Alloy Structural Steel

A325M Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength (Metric)

A490M Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)

A563M Specification for Carbon and Alloy Steel Nuts (Metric)

A588/A588M Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance

A709/A709M Specification for Structural Steel for Bridges

A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

D3951 Practice for Commercial Packaging

F436 Specification for Hardened Steel Washers

F568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric)

F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric)

F1136M Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners (Metric)

F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

F1789 Terminology for F16 Mechanical Fasteners

G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels

ANSI Standard

Keywords

carbon steel; metric; steel; washers; weathering steel; Fasteners (metal)--specifications; Hardened steel washers; Steel washers; Washers/washer assemblies--specifications ;

ICS Code

ICS Number Code 21.060.30 (Washers, locking elements)

DOI: 10.1520/F0436M-04

ASTM International is a member of CrossRef.