Search book title
Filters:
FORMAT
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(338)
ACI
(589)
AECDAILY
(599)
AISC
(55)
ASA
(234)
ASCE
(1006)
ASHRAE
(690)
ASME
(2183)
ASSE
(117)
ASTM
(95207)
AWC
(63)
AWWA
(575)
BHMA
(124)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(95391)
CHD
(3)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(322)
IEEE
(6938)
IES
(241)
ISEA
(21)
Joint Commission
(184)
Joint Commission Int.
(1)
NETA
(6)
NFPA
(1667)
TCNA
(17)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(25)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • BSI
    21/30433197 DC BS ISO 34-1. Rubber, vulcanized or thermoplastic. Determination of tear strength - Part 1. Trouser, angle and crescent test pieces
    Edition: 2021
    $44.66
    / user per year

Description of 21/30433197 DC 2021

This document specifies three test methods for the determination of the tear strength of vulcanized or thermoplastic rubber, namely the following:

  • method A, using a trouser test piece;

  • method B, using an angle test piece, with or without a nick of specified depth;

  • method C, using a crescent test piece with a nick.

The value of tear strength obtained depends on the shape of the test piece, speed of stretching, and temperature of test. It can also be susceptible to grain effects in rubber.

Method A: Using a trouser test piece

Method A, using the trouser test piece, is preferred because it is not sensitive to the length of the cut, unlike the other two test pieces in which the nick has to be very closely controlled. In addition, the results obtained are more easily related to the fundamental tear properties of the material and are less sensitive to modulus effects (provided that the leg extension is negligible) and the rate of propagation of the tear is directly related to the rate of grip separation. With some rubbers, the propagation of tear is not smooth (knotty tear), and analysis of results can be difficult.[3]

Method B, procedure (a): Using an angle test piece without nick

This test is a combination of tear initiation and propagation. Stress is built up at the point of the angle until it is sufficient to initiate a tear and then further stresses propagate this tear. However, it is only possible to measure the overall force required to rupture the test piece, and, therefore, the force cannot be resolved in two components producing initiation and propagation.[4]

Method B, procedure (b): Using an angle test piece with nick

This test measures the force required to propagate a nick already produced in the test piece. The rate of propagation is not directly related to the jaw speed.[5]

Method C: Using a crescent test piece

This test also measures the force required to propagate a nick already produced in the test piece, and the rate of propagation is not related to the jaw speed.

NOTE

A separate method for the determination of the tear strength of small test pieces of rubber (Delft test pieces) is specified in ISO 34-2 .[1]



Standard Number21/30433197 DC
TitleBS ISO 34-1. Rubber, vulcanized or thermoplastic. Determination of tear strength - Part 1. Trouser, angle and crescent test pieces
StatusDefinitive
Publication Date2021-08-24
Identical National Standard OfISO/DIS 34-1
DescriptorsTesting conditions, Rubber, Tensile testing, Tear tests, Mechanical testing, Synthetic rubber, Test specimens, Test equipment, Vulcanized rubber, Dimensions, Plastics and rubber technology, Shape, Force measurement, Thermoplastic polymers
ICS83.060 Rubber
CommitteePRI/22
PublisherBSI
Pages22

About BSI

BSI Group, also known as the British Standards Institution is the national standards body of the United Kingdom. BSI produces technical standards on a wide range of products and services and also supplies certification and standards-related services to businesses.
GROUPS
X