Cart (0)
  • No items in cart.
Total
$0
There is a technical issue about last added item. You can click "Report to us" button to let us know and we resolve the issue and return back to you or you can continue without last item via click to continue button.
Home
Content
Tour
eLibrary
Store
Search book title
Filters:
FORMAT
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(337)
ACI
(589)
AISC
(54)
ASA
(234)
ASCE
(996)
ASHRAE
(657)
ASME
(2161)
ASSE
(117)
ASTM
(94394)
AWC
(54)
AWWA
(568)
BHMA
(124)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(94534)
CHD
(3)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(315)
IEEE
(6631)
IES
(241)
ISEA
(16)
Joint Commission
(184)
Joint Commission Int.
(1)
NETA
(6)
NFPA
(1646)
TCNA
(17)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(25)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(31)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • BSI
    PD CEN/TS 17176-3:2022 Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure. Oriented unplasticized poly(vinyl chloride) (PVC-O) - Fittings
    Edition: 2022
    $435.35
    / user per year

Description of PD CEN/TS 17176-3:2022 2022

This document specifies the characteristics of solid-wall oriented unplasticized poly(vinyl chloride) (PVC-O) fittings for piping systems intended for water supply and for buried drainage, sewerage, treated waste water and irrigation under pressure or above-ground where protected from direct sunlight. The scope of this document is limited to double sockets, repair couplings, reducers and to non-end load bearing elbows. NOTE 1 The scope of this document is restricted to fittings on the market during the preparation of this document. Therefore, tees, flange adaptors, etc., are excluded from this version of the standard. NOTE 2 For double sockets, repair couplings and reducers there are no special fittings designs for end-load bearing applications. However, restrained gaskets can be used for end-load bearing applications. In that case, the requirements of EN 17176-5 are applicable. It also specifies the test parameters for the test methods referred to in this document. In conjunction with EN 17176-1 and EN 17176-5, this document is applicable to oriented PVC-O fittings intended to be used for the following: a) water mains and services lines; b) conveyance of water for both outside and inside buildings; c) drainage, sewerage and treated waste water under pressure; d) irrigation under pressure. This document is applicable to piping systems intended for the supply of water with a maximum allowable operating pressure (PFA) up to and including 25 bar . The piping system according to this document is intended for the conveyance of cold water up to and including 45 °C and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations. For temperatures between 25 °C and 45 °C, EN 17176-2:2019, Figure C.1 applies. This document specifies a range of fittings sizes and pressure classes and gives a requirement and recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Standard NumberPD CEN/TS 17176-3:2022
TitlePlastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure. Oriented unplasticized poly(vinyl chloride) (PVC-O) - Fittings
StatusDefinitive
Publication Date2022-06-30
ReplacesPD CEN/TS 17176-3:2019
Identical National Standard OfCEN/TS 17176-3
DescriptorsPipe fittings, Pipe couplings, Pipework systems, Dimensional measurement, Test equipment, Accuracy, Pipes, Angular measurement, Diameter measurement, Tolerances (measurement), Geometry, Thickness measurement, Flanges, Plastics
ICS23.040.20 Plastics pipes, 23.040.45 Plastics fittings
CommitteePRI/88
ISBN978 0 539 18849 3
PublisherBSI
Pages28

The following editions for this book are also available...

About BSI

BSI Group, also known as the British Standards Institution is the national standards body of the United Kingdom. BSI produces technical standards on a wide range of products and services and also supplies certification and standards-related services to businesses.
GROUPS
X